Forum Replies Created
-
AuthorPosts
-
2012/01/12 at 11:22 pm #29956
OOoooo Andy this is GREAT!!! Yes… this is superb!!! A&H please do similar..))
Mario from Poland.
2011/07/19 at 7:06 am #28801Please add this feature than i press RESET and channel SEL the panorama also may reset to center. Now panorama after reset is the same that before reset. Could you?
Mario from Poland.
2011/05/04 at 10:13 am #28160Hi
Ok i try this next timeRegards
Mario2011/04/26 at 7:49 am #28086Hey
You can doit this way:
1. Create 2 matrix groups – one to main L-R, second to the outfill
2. Leave the EQ on main L-R and add EQ on matrix only
Its works great
Bonus: You can record the show from L-R without EQMario from Poland
2011/03/03 at 6:10 pm #27628ok its ok everything works great
Mario
2011/03/03 at 5:16 pm #27625hey
this link not solve my problen because link in this link is death and i still dont know how set the second pc to surface.Best regards
Mario from Poland2011/01/26 at 7:06 am #27121hey
Yes yes all thas check. There is no signal input on leds. After few hours the same show file and scene and this channels are working again. Thats is problem with mixrack.Cheers
Mario2011/01/25 at 9:22 pm #27118Ok on the next job i doit for you
I have now diffrent problem. After boot up on the latest show first channels from A1 to A8 are totally dead. No signal. I have move input channels to diffrent “8” and all input are ok. After this job system is back to my storage place and i have turned it again and this channels from A1 to A8 is good now… What the? Is possible?Regards
Mario2011/01/24 at 11:39 am #27109Hey
Ok thx.
I have only connected then an iLive and Mixrack without any laptops and routers.Regards
Mario from Poland2010/11/29 at 7:22 am #26846In my case main board of IDR is fail. Service chenge this and now is OK. Strange… but happen sometime
Mario from Poland.
2010/11/16 at 9:28 am #26784hello
I have the same problem but…
I have problem that during the show my board is stop playing any sound. I have select any channel and the gain reduction on compressor and limiter are fully red to the end and have no input signal. I have reboot the system and surface cannot link to IDR and i see the text “idr mix rack boot failure”. My mixer is now in polish service and i am waiting for the reason what happend.Mario from Poland
PS. Service in Poland is great. They bring me an backup mixer and IDR for my show THX Konsbud Audio!!!
2010/10/26 at 10:12 am #26673quote:
Originally posted by grahamwhiteMy T112 does this too. Although as Stealth suggests it may be because i have the “fill” activated.
I have tried with FILL on and OFF. It has nothing to do. This problem remains.
Mario from Poland
2010/10/25 at 7:09 am #26662Hello
I have iLive T112 and IDR 48 and after update to firmware 1.7 have the same problem. Before that thas was quickest. Now then i have open the EQ window and pres SEL on every channel i must wait 1-2 sec then the EQ graph is change. It has nothing to do with FILL option. Without this option also must wait. Now i have made updgrade to 1.71 and this probles remains. Its very annoying.Cheers
Mario from Poland.2010/10/06 at 6:14 pm #26587No one have tried this?
Mario
2010/10/03 at 6:27 pm #26557I know that first 3-4 second must wait. But later then the channel is alright make quick change in gain channel (not trim). Then you can hear again “shots” – there is no microphone. Try it in your ilive system.
Best regard
Mario -
AuthorPosts