Forum Replies Created
-
AuthorPosts
-
2020/02/20 at 11:24 am #89726
Hello ctrumpower23!
Encoders are soldered direct to the circuit board, but it will be replaceable. I think that excatly that encoder might be easy to replace.
Here is some pictures where you can see (pic 3) that encoder is placed small circuit board next to the touch screen.
I have replace one of those EQ-encoder, as you can see one of those pictures. 😉
Hope this helps!Make
2019/08/15 at 6:36 am #858702018/12/03 at 4:54 am #80504@mfk0815 This is actually not true. I tested signal flow earlier as you can read in my earlier post. 😉
2018/10/21 at 6:16 am #79433@biggsounds Limited to 16 ins, if you use SQ5 local inputs, but adding another SLink card to SQ, you can add more inputs, or use SQ6 or SQ7.
SQ accepts returns also. So, if I have GLD in FOH and SQ in mon, I can send main L & R signal from GLD to SQ.
I have limited time to test every scenario, but this looks very promising for FOH & MON configuration.
2018/10/20 at 7:56 pm #79428I just tested, and yes, direct connection between GLD and SQ is possible! You can route input signals from SQ to S-link and connect cat-cable from SQ:s S-link port to GLD Dsnake port. Working fine! It needs a little bit of ins and outs configuration, but it works. 🙂
If you need more than 16 inputs, then you need another S-link card, where you can connect for example AR2412 stage box.
2018/10/02 at 10:11 am #78859Hello!
Earlier I did some maintenance to my GLD, so I posted some pictures to the forum. You can find them here: https://community.allen-heath.com/forums/topic/inside-gld80
It is not so complicated to open this desk, but if I remember right, there is some cables which are very tight when you open the chassis. Be careful and good luck. 🙂
2016/04/27 at 5:04 pm #55315I was doing it few times with drummers monitor/wedge. But I did it little bit more complicated way, because I route ME-1s output back to FOH console, so that I can do equalisation and have so called “master control” in that monitor feed. It was actually working very nice. 🙂
2015/05/01 at 8:44 am #47691I have done that few times. My GLD with dante card is the monitor desk, and we have Yamaha CL3 at FOH desk. In stage we have Yamaha Rio-stagebox, wich have dante port. Connect one cat-cable from Rio stagebox to GLD dante port and configure GLD to use dante channels to channel inputs and configure audio sync to use option card clock. It works flawlessly. 🙂
You must remember that the channel gains is set by the foh-desk and you must use channel trim in GLD.
Once system is gonfigured, its very simple and fast to setup and use. High five to Dante! 🙂
2015/04/10 at 10:26 am #46747My iPad(4th gen,retina) app works very well. You may try to remove app from iPad and reinstall it. I have problems with earlier versions, and they solved by reinstall apps. Hope this works!
2014/03/07 at 4:52 am #38126I have problem with iPad app. When I choose demo-mode, app shuts down. Same with One mix app. Not tried with the desk yet. Anyone else have this same problem?
Problem solved. I remove and reinstall GLD remote app, and now it works! I think that some kind of improvement is done about appearance of the app. Now it looks like a little bit clearer… Or maybe I imagine it is better than the older one. 😀
2014/03/06 at 7:41 pm #38102I have problem with iPad app. When I choose demo-mode, app shuts down. Same with One mix app. Not tried with the desk yet. Anyone else have this same problem?
2013/02/06 at 11:13 am #32999Thanks for info Woutert! I just purchase one extra license.
GLD + AR2412 + Dante
2013/01/20 at 8:13 am #327502012/11/21 at 9:59 am #32199quote:
Originally posted by clarocqueMaybe a little off topic, but what if you have a GLD connected to iLive as a MON desk.
Just to confim, should the GLD clock in the mixer be set to internal or Option card?
I have used that kind of set once, and I set GLD clock sync via option card and that works great.
GLD + AR2412 + Dante
2012/10/08 at 8:14 pm #31619Sorry, I borrow this topic a little.
Must ask… I try to buy Dante card from our local dealer. Now I have already been waiting about 7 weeks and still waiting. What is the problem that A&H can’t deliver those cards to dealers?
Thanks in advance.
GLD + AR2412
-
AuthorPosts