[plevrierParticipant]

Yes it works

You need 1 dante card per console

No swith required. You can connect the multitrack recorder to the secondary ethernet port of the dante card. It must te configured in switch mode.

Yes you can still use a 2412 and split it for FOH. For each dsp channel you can choose any input in the patch section or pre-amp page of the channel at the FOH board. Keep in mind that the monitorboard is owner of the preamp gain.

Regards,
Pascal

[plevrierParticipant]

Works but you have a clocking issue. You will hear ticks and gliches.

[plevrierParticipant]

Are you using a matrix to feed the livestream ? If so, try routing it Pre-Mains LR and set the matrix out to unity. aldough I think you are running all levels relativly low if you have noise on outputs.

Regards,
Pascal

[plevrierParticipant]

Most of the time I use this setup:

FX1 : H481 live with a time of +/- 1,5 sec – Vocals
FX2 : Delay long with 50% feedback – Vocals (on global tap 1/4 note)
FX3 : Delay short (slapback) 0% feedback – Vocals (on global tap 1/16 note)
FX4 : Doubler / Rotator
Rotator only setup for use of Tube Drive to Max. To get harmonics for Vox / OH
FX5 : EMT with a time of +/- 1,0 sec – Instruments (guitar / keys / horns…)
FX6 : Dynamic EQ on vocals group bus
FX7 : De-esser on main vocals
FX8 : Gated Verb / Transient Controller (what is needed for the type of music / show)

Hope this helps for you.

regards,
Pascal

[plevrierParticipant]

I already started a “firmware update” question some time ago. Too bad that nobody from the A&H crew takes time or is willing to respond. Basically you ask the same. As I look at Qu series, they have better remote control (full control on an ipad and Qu-me for iphone and android). I am annoyed that the more expensive platform GLD didn’t have any update or announcement what is to come in the (near) future.

Due to lack of communication I wont buy a new GLD and take my chances with a console that is updated.

[plevrierParticipant]

So today I saw the webinar for dLive. I like that console but for now I am still waiting for any changes / updates for GLD ?

WHAT IS THE PLAN ? Please A&H I am asking for a long time now. Take just 1 minute to reply and state what the future is for GLD.

[plevrierParticipant]

Well no response from anybody from A&H. I am disappointed. It seems that GLD platform is what is it for now and no updates. That is a shame. the Qu platform has some really nice features in the Remote Apps which are not in GLD.

So please A&H share your roadmap for GLD.

[plevrierParticipant]

It has been a year now since the last update. (1.51).

I am still hoping for some bugfixes and new functionality as it is also done in de Qu series.

Can anybody from A&H clarify the roadmap for GLD series ? If this is it, I will still use the GLD but for a new console I will check out other manufacturers as well.

regards,
Pascal

[plevrierParticipant]

That is correct. Multi channel recording is only supported by using a card in the extension bay.

USB recording is supported but limited to 2 channels. By default configured to record REC matrix, but in fact you are also able to record 2 mono groups or input channels. (Press assign in the Player / recorder screen).

Hope this helps you out.

regards,
Pascal

[plevrierParticipant]

you can patch pfl to any output in the I/O screen ? I am sure I am missing the purpose how you are using the gld.

[plevrierParticipant]

you can make alt out with a matrix output ? just route Main to it on pre fader. works fine

[plevrierParticipant]

I know that problem. I would like to change the FX send settings, but so sad that the AUX sends are in the same safe state, so i lose my mon mix sends for the musicians. That is a no go. I changed my way of working and only change the FX effect itself and some good planning which channels / sends i can leave in the same state.

[plevrierParticipant]

Since wifi and dsnake are 100 Mbit connections, you can do a hardware split on your cat5 cable. Use 2 pairs for dsnake, and 2 pairs for wifi.

Works like a charm. An yes simple to make. Looks a bit stupid ? Agree, but saves using switches with vlan circuits. I use it to connect an artnet dmx output controller.

Regards,
Pascal

[plevrierParticipant]

With a good EQ setup (bandpass) some compression and the Rotator as an insert you should get really close. Just use the drive preset and set it to full drive and play around with the LF/HF knob. (And dry/wet).

The drive in the rotator works pretty well, aldough I would like a tube emulation of a distortion box.

Regards
Pascal

[plevrierParticipant]

Well, i would like to see that labeling is possible. So add a textbox in the softkey setup screen and show those labels in the main view instead of the big GLD logo.

i use so many different softkey layouts in my shows, so something like a simple label helps me a lot.

Regards,
Pascal

[Author]

Posts