Forum Replies Created

Viewing 15 posts - 1 through 15 (of 50 total)
  • Author
    Posts
  • #103985
    Profile photo of Loloverde
    Loloverde
    Participant

    Hi

    I use the right side widget just as a jumping point to the main window of the gate or compressor. So I never have the only compressor widget on. That’s the reason, I did not see it.

    I played a little bit with the different firmware versions:
    In 1.87 flat means a value of 31. In 1.9 flat has a value of 22.
    If you store a flat emphasis in 1.87 you will have a flat emphasis in 1.9.
    At least on the user interface the emphasis is the same in both versions.

    #103981
    Profile photo of Loloverde
    Loloverde
    Participant

    Hi RS

    Just to clearify: You speak about this little potentiometer under the side chain selection.
    In 1.9 you can set the emphasis to 80/5K, 80, flat and everything on the left side.

    Where can you read the value “22” on the surface or director?

    bye
    Rainer

    #103252
    Profile photo of Loloverde
    Loloverde
    Participant

    Howdy

    The DX168 will not show up in the Dante controller, because it is not a Dante device.
    You can route the DX168 inputs to Dante in the dLive routing window on the surface.

    bye
    Rainer

    #98692
    Profile photo of Loloverde
    Loloverde
    Participant

    For the record: It wasn’t the new software that made the clicks. It was a wrong setting.
    If fixed it after reading this thread:

    dLive Dante recording noise

    #98624
    Profile photo of Loloverde
    Loloverde
    Participant

    I think I try a downgrade. It run smoothley with 3.4.15.

    #98616
    Profile photo of Loloverde
    Loloverde
    Participant

    Thanks for the quick answer. How much did it cost?

    #98596
    Profile photo of Loloverde
    Loloverde
    Participant

    Hi Steffen

    So you updated the hardware, because the new software wasn’t working?
    Where did you purchase the new Brooklyn bridge?

    bye
    Rainer

    #96848
    Profile photo of Loloverde
    Loloverde
    Participant

    +1

    Or is there something new yet?

    #89625
    Profile photo of Loloverde
    Loloverde
    Participant

    That’s CTRL for non german Keyboards.

    #89612
    Profile photo of Loloverde
    Loloverde
    Participant

    Howdy

    On a Windows PC: hold down STRG and you will get 0.1m steps.

    bye
    Rainer

    #88449
    Profile photo of Loloverde
    Loloverde
    Participant

    Howdy

    Thanks to the now available manual I know, that they are as with dLive Stereo or mono.

    bye
    Rainer

    #88306
    Profile photo of Loloverde
    Loloverde
    Participant

    The picture

    Attachments:
    You must be logged in to view attached files.
    #85410
    Profile photo of Loloverde
    Loloverde
    Participant

    You have to push the Setup button.

    #84865
    Profile photo of Loloverde
    Loloverde
    Participant

    Howdy

    Because of your remark I made a quick internet search and found that:

    Using Elgato Stream Deck with dLive

    It’s just a week old, so no wonder nobody knew.

    bye
    Rainer

    #84862
    Profile photo of Loloverde
    Loloverde
    Participant

    Howdy

    Does anybody use the Elgato Stream Deck for additional soft keys?

    bye
    Raner

Viewing 15 posts - 1 through 15 (of 50 total)