[WolfgangParticipant]

sorry, double post…

[WolfgangParticipant]

I always use a mono-matrix called STAGE, to which I can simply send the talkback microphone in the talkback window.
in the I/O window I route this matrix to a channel for the ME-1 and place it there on a button.
only when I press “TALK”, a signal goes to this matrix

but you can also simply use a microphone with a switch…

[WolfgangParticipant]

why create a softkey to clear the PAFLs?
on the surface there is already a button for this function, directly below the master level indicator

[WolfgangParticipant]

Yes, you can do that well with aux. an aux does not always have to be prefade 😉

Nevertheless, this question about channels-to-Matrix will keep reappearing, because many technicians are so used to it from Yamaha.
it might therefore be a good idea to implement this in dLive, so that this theme, which has been recurring for many years, can finally be brought to an end. 😉

[WolfgangParticipant]

we will see if there are enough requests from other colleagues for this change.
I hope so … 😉

[WolfgangParticipant]

+1

I also use the IP8 with a S3000.
I usually use the IP8 module for drum channels, mix-sends or subgroups.
an improvement of the function for AUX-sends would also be in my interest.

which I think is also good, if you could use the spill-features of the DCA-groups with the IP8! ; -)

[WolfgangParticipant]

I didn’t have any errors with the dLive
is there no support in your country?

look here:

Home

-> Contact A&H

[WolfgangParticipant]

but that’s been around since the beginning. 😉

[WolfgangParticipant]

I know the situation Albin mentions. for example, it is about a short-term failure of the power supply.
I pointed this out a long time ago.

In my opinion, the problem lies in the fact that the preamps get a very high sensitivity for a moment when the phantom power is switched on again. it’s very short, so the feedback is very short. but it can be very annoying.
the better method has to be: mute the INPUTS for a moment; -)
it would therefore be very helpful if the time to unlock would be a little longer, so that the circuits can adjust themselves accordingly.

[WolfgangParticipant]

+1 a link to the seminars is also good for me
I couldn’t watch the second seminar because I had too much work.

the first seminar for version 1.60 was very interesting, thank you for that!
as I had already written before, I would like to find a solution that allows you to activate the gain tracking for several preamps at the same time.

one more question: when will 1.60 be online?
the “Mighty Compressor” interests me very much and I need the copy possibility of the “Recall Filter” urgently.
and – many thanks for turning off the hum in the Echo-FX !! 😉

[WolfgangParticipant]

to 2)
full consent!
The proposed better resolution for the PAN would be helpful!

And I still want a copy&paste function for copying EQ settings
When editing monitor paths on stage, I don’t want to run back to the mixer to copy the found settings in the other ways.

[WolfgangParticipant]

yes, but BILDIC asks was whether A&H can change this. the Dante-chip permits higher data rates

[WolfgangParticipant]

this is not the same.
for example: in the dLive you can´t define a 24dB Linkwitz-Riley Lopass-filter.

+1 from me for the Speaker Matrix – or, as I said before, to have an option of Hi- and Lopassfilter in the mixes. please! 😉

[WolfgangParticipant]

+1 !

[WolfgangParticipant]

i have the same problem with a Lenovo Yoga PC and sent fotos to the distributor.
when I scale the touchsreen-size more than 2/3 of the slider, the grid is not correct.
this problem exists without external screen too.

[Author]

Posts