Forum Replies Created
-
AuthorPosts
-
2017/10/24 at 9:11 am #65824
Video attachment
2017/10/24 at 9:08 am #65823Thanks Nicolas for the Answer – i sucessfully used it on my last monitor-job! Although i’ve got some suggestions:
If I press PAFL of an Input Channel, and this one is not assigned to either wedge or IEM – the PAFL comes in full volume out of my che wedge.. i see that other engineers always turn the cue wedge fader down before PAFL any other channel.. but it costs you more time to do so!
So I thought I’m a genius and assign all the Input Channels only to IEM! In this case after cue-listening to an Aux, I can press PAFL of an Input without fading my cue-wedge down to hear the channel in my Headphones! That worked so far.. but here’s the problem:
The sequence of “muting the cue wedge, and PAFL the Input” is “wrong”! Before the cue wedge is muted the channel is PAFLd! Means you get a short signal from the input to the cue wedge!See the attached video (although in german) where you can hear the short noise while swapping from cue wedge to IEM!
2017/08/12 at 5:18 pm #64781Do you have any oltion card installed? Sounds like a wolrd clock issue! Check in the setting/audio/sync if the world clock is set internal or to the option card (in case you’ve got an extension card installed!)
2017/01/10 at 3:12 pm #60478it’s an old thread.. but i’m still missing it: Bookmarks for Pages to assign by softkeys (like the Yamaha Desks)
for GLD and dLive with just one screen would this be super handy!
2017/01/10 at 3:10 pm #60477What about combining the c-Range with the “full” dLive: Can I use de S5000 with the CDM48? (not redundant – i know)
Since now.. i’ve never used redundant PSU or Network.. so for me a way to save money on the mixrack but still would like to have the S5000 Surface with the loads of functions!?2016/09/09 at 9:19 am #58064same here: I sent my AR2412 to my dealer, he replaced the PCB and now it works fine again!
2016/06/13 at 6:48 am #56536I’m an Idiot! Thanks Bob! After checking the block diagram: Delay is only included if I set the Global Output source per mix to “post all”!
Thanks for your help!
2016/01/25 at 10:12 pm #53567Got my repaired AR2412 back today – it looks like working fine again! Ordered an AB168 as extension/backup – 40XLR Inputs on Stage.. wohooo ;D
2016/01/13 at 8:43 pm #53287George.. Do you know google? ;)as I expected.. CHF and USD is almost 1:1! So lets say around 230USD (incl work and delivery)
2016/01/13 at 10:14 am #53269I just got the information from my dealer that they have to replace the PCB and not the power supply to fix this boot-up problem! Cost me about 230CHF to get it fixed! Hope that was the issue! Keep you up-to-date when I got back my stagebox!
2015/12/23 at 7:41 am #52905Hi everyone! Is there a solution on a failing power up? Just had the same issue with my AR2412… Fan starts working but blue Power-Light needs a boot up up to 15min till it works! I will send mine in to my A&H dealer! Looks like a power supply issue!?
2015/11/06 at 12:38 am #51906Thanks Andreas for your answer but actualy it’s clear what I need:
2 scenes!Scene 1: “FoH ON – scene”
All Inputs are assigned to the Main LR Mix (all parameters should be blocked out of recalling except the “assign routing” from all the Inputs to the Main LR)Scene 2: “FoH off – scene”
In the concert breaks I want to load scene 2 to “unassign”
all input-channels except the ST1 (st1 = background music) from the Main LR but still run instruments through InEar Monitors!As far as I see there’s no individual filter for “assign” only! It’s connected with fader-level and during a gig these settings might need to get changed! (I would say the “routing mix sends” is the filter that includes assignments!?)
Solution would be using a DCA where all Channels except ST1 is assignes and turn it down in between the sets.. But I would rather safe my customlayer-faders for live adjustments!
In a further software update you could add a special mute setting that allows you to mute channels just on the Main LR but not on monitors… I would say loads of people would love to use this feature!
2015/11/05 at 10:56 pm #51903I’ve got a customer right now with the same question… Still see a problem due the “volumes” change also with the “assignment” in a scene!
And just to clearify.. You need to set in both scenes (foh and no foh) all filters on “block” except the “routing – mix sends”! Because the only thing you want to recall is the “assign” settings! Right!?
Only solution in my opinion is to use a DCA Fader and set them to zero!
2015/10/06 at 8:46 pm #51128If you implement this then please as a optional function.. Don’t like that at my GLD! Can occur unwanted changes!
2015/10/01 at 5:46 pm #51004Waiting for v1.9 when we can use stereo mixes as groups or matrixes (would be awesome for Qu-16 user!)
-
AuthorPosts