Forum Replies Created
-
AuthorPosts
-
2020/04/24 at 11:41 am #91315
this is most likely because the SQ sends the audio stream in 96khz and logic is set to work in 48khz. set your sample rate in the logic project to 96 khz and the problem will disappear.
2019/12/25 at 9:15 am #88402I think it should be fine. I think the limit is 2 concurrent sessions of mixpad.
2019/12/04 at 8:29 am #88047would love dca spill too
2019/12/02 at 10:25 pm #88030My workflow is centered around one principle: it’s really hard to make a turd pleasant by polishing it. It’s really hard to fix bad sound in any console, and you need to really know what you’re doing to get good results. It’s much easier (and more fun) to enhance good sound with a console.
1. My workflow ALWAYS starts with microphone (or d.i box) selection.
2. When a mic has been selected positioning the mic properly is crucial. (For singers mic technique is also important) for electronic drums, make sure they sound good coming into the mixer. If it’s only a stereo input, you’ll be somewhat limited in what you can do with them in the console.
3. Set gain so you get a good, strong signal without clipping and feeding back.
These three should get you to at least 95% of the sound you want (given that the PA is in good shape)
4. After this set high pass filter if it feels too muddy in the low
5. Eq
6. Compression (on vocals I usually do between 1:2 -1:3 ratios, fairly standard attack and release times, there is a great video on compression Here , it’s recorded in Logic Pro but you’ll find the same parameters in the sq compressors)
7. Add Reverb and delayNo compression, eq or fx plugins are going to consistently shape your sound like you want it unless the three first points are done properly.
2019/10/08 at 11:13 am #86893i have had no issues since updating.
2019/09/27 at 1:31 pm #86671This is no longer an issue after updating to iPadOS
2019/09/17 at 6:27 pm #86518So I’m on an iPad Air 3rd gen. Could that be the reason for this?
2019/09/17 at 2:07 pm #86508huh. which ipad are you on?
2019/09/17 at 12:41 pm #86503it works on ipad as well, the problem is more of a design issue – the sofware keyboard covers the dialog box, so the dialog box should be moved so it can be completely visible even when the keyboard is activated. as it is now one has to remove the keyboard from the screen in order to sve the setting or choose the lowest row of colors.
2019/09/12 at 7:54 pm #86351Only thing I’ve done is set project sample rate to 96 kHz. Everything has been fine after that
2019/09/09 at 7:38 am #86283I’d use input ganging instead of running it as a stereo channel
2019/09/02 at 3:46 pm #86163Oh I understand that it’s not just a code five-line code addition. It’s a feature I’d like to see though.
2019/08/28 at 3:52 pm #86098Thanks, so are the dx stageboxes incompatible with the option card or is it impossible to run the dx boxes on both the slink port and the slink option card at the same time?
2019/08/28 at 10:29 am #86090i’m using a 2012 macbook pro retina without any issues so far. don’t forget to set up the project in 96khz though, i use logic and it complained that the hard drive was too slow whenever i ran the project in 48k. (probably due to the computer having to convert everything to the project sample rate in real-time…)
2019/08/27 at 8:16 am #86058i second this request
-
AuthorPosts