Forum Replies Created
-
AuthorPosts
-
2020/01/08 at 7:14 pm #88636
I also look towards the 1U River of the MIDAS M32C remote control – It surpasses the QU-SB by a lot .. Qu32, respectively .. A total of 8 to eight quality effects (to which you can assign GEQ, etc.) … Someone asked which way who Looks … Here in the end, where exactly do I look now … Thanks for that QU-SB and digital noise / distortion.
2020/01/08 at 6:22 pm #88635electrical clicks when working with the QU-SB remote control have become even Stronger ((And This is NOT a problem because of 3.0 …. On my computer (which was built in 2007) there are boards Only with USB 2.0 …. I have a disk High-speed SSD / Vidovs10 / 64 Pro … And the digital noise as it was, it’s gotten even stronger … It’s just some kind of trouble …. We’ll have to look for a modern river mixer, which will be by Quality of compressors / pre amplifiers and effects, match or will be Better than QU-SB … I have now determined for myself the highest quality device (mixer with the best quality from All options c) – this is UNIVERSAL AUDIO Apollo 8 QUAD or higher (with a large number of inputs and outputs) … The best and the smallest in size are simply not to be found, it seems to me … But here the Quality and Price will be increased ..
2019/12/02 at 6:19 am #88017Tell me, so what is the delay in mile seconds (ms) for the Qu series? When we send a signal from a computer to any channel – and then add this channel to Group 1-2, it’s impossible to listen to these two signals at the same time … a strong delay unfortunately … And there is no Patching on the channels either … How then can we make several Identical voice signals, but process them differently and without delays ???
2019/11/11 at 4:44 am #87553I have the same thing !!! When I upload native Loops to Studio One … And it started (as I think) when I downloaded the New driver for Asio on Wondows10 from the Official Allen & Heath website! The same strong distortions also started when listening to any music on some Sites – for example, VKontakte! Just Horror! And on the previous firmware for Asio, this wasn’t .. The developers are obliged to check it! And fix the problem! My mixing console is QU-SB.
2019/10/21 at 10:28 am #87257money for the WIND.
2019/04/27 at 5:19 am #83557Good day .. I still expect any instructions to identify my problem with QU? And what conclusions, after all that you wrote to do, did you do? What should I do next with a mixing console?
2019/04/22 at 2:35 am #83466Do you have any suggestions or suggestions on the last letter described above? Or is our situation a hopeless situation?
2019/04/20 at 6:52 am #83441Well, we all seemed to be able to – checked … All physical exits that are available in QU-SB … How else can we narrow down the search range? What other experiments to do? Today we turned on the console – and at the same time we heard from monitors and headphones … The clicks were only in the monitors – which are connected to Maine .. And for 99.996% clicks only from the “R” outputs … from the left click output, as a rule, No …. Just checked today the MTX1-2 outputs, the clicks are exactly the same – as I had anticipated … It was possible not to check .. From all the inputs I took out the XLR-to eliminate the situation that you described about cal clicks from microphones and carpet … All – options to narrow the range of just over …
2019/04/19 at 1:47 pm #83430I checked the headphone out … There are clicks too, but very very quiet, compared to those on all the outlets … As I understand it – this does not solve anything … This is a defective product (And I find it very strange – why QU -SB NO full-fledged power switch ??? It’s just Nonsense !!! When plugged into the outlet, too, Beats a click …- well, and then it all Lives its life … Steady after 30 minutes of the console – clicks Stop … And so until the next new Inclusion ..
2019/04/17 at 12:14 pm #83391I will listen to the headphones of course, but … If they have the same clicks, or there are no clicks, what will it change? To where does the location of this problem narrow? And what could be the problem? What is your guess? To me – as an amateur in electronics, it can only be assumed that this is possible because of some kind of faulty resistor / transistor, or something like that … What else can accumulate and release such electrical clicks – I can’t even assume .. Exits like you indicated – ALT OUT or 2TRK OUT – I do not have the same … I have the remote control – model QU-SB.
2019/04/17 at 5:07 am #83386Hmm .. Headphones have not yet connected to the remote control …. But I connected everything to the output monitors (output mix) … I put Mute – I lowered all the faders, to understand the reasons .. But the clicks still go away – it does not stop them. .. Of course I’ll listen in headphones – but what difference does it make? I don’t need headphones. I need Mix – to give monitoring to a radio …
2019/04/16 at 12:55 pm #83377There are no problems with cable products – all cable products are custom-made at Better Kabel.The QU-SB is connected to the ADAM. studio monitors. These clicks / electric clicks are usually often after turning on the console into an electrical network (given that I have a good power stabilizer.), it rarely happens that there are no clicks at all, but more often they are … Then there are very few of them in the first 15-20 minutes after switching on, and then they stop, there are many / often – but after a while everything stops … And so every day / every Kticheski times after first turning on QU ..
2019/04/16 at 3:18 am #83366Tell me please – does anyone have a pulse, shots of electric clicks in columns / monitors from all exits from QU? This problem is also heard in the columns even if we completely turn off the Master channel or Mix channels – Mute also does not stop these Chaotic spontaneous electrical clicks / signals … Tell me what it is – how to fix it … We changed different firmware / versions firmware .. And they made a hard reset – but all without success … Nothing helps – clicks still happen … What is this ???
2019/04/05 at 12:34 pm #83192Tell me please – does anyone have a pulse, shots of electric clicks in columns / monitors from all exits from QU? This problem is also heard in the columns even if we completely turn off the Master channel or Mix channels – Mute also does not stop these Chaotic spontaneous electrical clicks / signals … Tell me what it is – how to fix it … We changed different firmware / versions firmware .. And they made a hard reset – but all without success … Nothing helps – clicks still happen … What is this ???
2019/04/02 at 3:23 pm #83103Hello! I installed the driver on XP 10 for the QU … At the bottom of the monitor, the right “&” appeared – clicking on it we see the Buffer Settings – and two tabs at the bottom: USB Streaming Mod, and ASIO Buffer Size .. Tell someone please – How do these parameters affect the recorded and reproduced sound from the computer / DAW? What parameters how to set / in what order / combination? And why do we need these parameters in general? For earlier Thanks for any answer.
Attachments:
You must be logged in to view attached files. -
AuthorPosts
