[CallumBParticipant]

quote:

---

Originally posted by millst

Unfortunately the belkin doesnt act as a dhcp server when in AP mode. Otherwise it would be perfect.

---

You really should try these: https://www.gowifi.co.nz/engenius-networks/engenius-ecb-1221r-250mw-wireless-router/bridge/wds/repeater.html

I’ve got a few, and they’re great. With a higher gain antenna on them, the range is impressive.

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

Ideally you woud configure the belkin as an AP, because when is configured as a router it’s going to be NATing everything on the wan side. Will the belkins not provide dhcp in AP mode?

Everything should be reachable if they are in router mode as long as everything is on e LAN port. I would avoid using the wan port, as it will only routebdat through it if it’s on a different subnet.

quote:

---

Originally posted by millst

Hi All

Just wondering how you guys setup your networking.
I have two i-live systems, each in its own rack with a 16 port switch and a belkin playmax.

Our workshop also has its own wired and wireless networking.
In an ideal world everything would be cross plugable without needing any configuration to use.

Our networks are setup as follows…

Workshop: 192.168.0.X 255.255.255.0
ilive1: 192.168.0.X 255.255.255.0
ilive2: 192.168.0.X 255.255.255.0

now this is all fine in a wired only world, i can plug each rack into our local network and access it using wifi in our workshop or via a wired connection. It gets tricky when you add wireless to each rack.

The question is whether to setup the belkins as AP’s or routers. I tend to lean towards routers because this gives you DHCP for laptops and Ipads which makes configuration easy.

However the question is whether to put the ilive network into a LAN port on the belkins or into the internet port, or to connect the workshop network into the LAN port or the WAN port. Each has its own advantages and disadvantages that are driving me nuts.

If i’m connected to the ilive wireless rack which is also connected to our local network, i’d still like to be able to print or use the internet. Also, if the rack is connected to the workshop network, then any PC on the network should also be able to access an iLive.
But, ideally if you connect to the iLive wifi network, opening the ilive editor on a PC should show all the ilives on the network, this isn’t possible if your ilive network is on the WAN port.

However, if I set the LAN network on each playmax to also be a 192.168.0.X range (same as the workshop) then I can’t actually route to the workshop if its on the WAN port as its the same network and confuses the router.

I’m thinking the only way forward is to:

workshop: 192.168.0.X connected to WAN port – playmax picks up workshop DHCP.
ilive1: 192.168.1.X connected to LAN port
wifi: 192.168.1.X with DHCP to clients and or LAN clients.

does anyone else have any thoughts and suggestions or can share their setups (especially if they are complex setups)?

---

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

I would suggest you have a look at the Audio Technica ath-m50 . I have found these t be very good.

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

I have been playing with it a bit, and have has the memory errors mentioned, I found the rebooting the iPad and opening mix pad only is a good way of preventing it.

Looks like I wont be needing a console for some smaller gigs now!

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

It’s live!

I’ve just checked the app store now and it’s online

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

Ill be getting some of the Ubnt M5 units in soon for another project, Youre welcome to try them with your desk before you buy if you like.

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

I have used the Ubiquiti products quite extensively, Unfortunately not in audio related applications, But I can testify to the quality of these products.
I generally get these from:https://www.gowifi.co.nz/

I have a few permanent wireless links in using a mixture of Ubiquiti and Mikrotik products, And I recommend them both.
I have posted elsewhere regarding a setup using mikrotik hardware, which has the advantages of band-diversity/redundancy and is infinitely more configurable than the UBNT hardware, But its at a higher price, and takes a bit of time to configure the hardware initially.

Callum Brieske
ML Consultants
New Zealand

[CallumBParticipant]

I would recommend getting a couple of mikrotik routerboards.
The RB433AH is a fairly powerfull router (Used by many wireless Internet Service Providers)
RB433AH https://routerboard.com/pricelist.php?showProduct=37
A Pair of those with suitable radio cards:
https://routerboard.com/pricelist.php?showProduct=69
IE four of the above cards, and antennas to suit the location.

The routers can then be configured to use both cards to increase performance, and provide redundancy incase one link fails.
One card can operate in each band 2.4/5.8 or they could both operate in the 5.8 band on different channels.

Mikrotik has distributors in most countries.

This setup will allow seamless layer 2 bridging, If all youre wanting is a router for use with a laptop, Then one of the RB433AH and one of the cards will suffice. I would recommend using the 5.8 band if your laptop supports is.

There are also some really nice rack mount enclosures available for these boards.

Callum Brieske
ML Consultants
New Zealand

[Author]

Posts