Replies Created | Forums | RB | Allen & Heath Digital Community

RB

active 7 years, 4 months ago

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 19 total)

1 2 →

Author

Posts
2015/02/24 at 7:01 pm #45576

RB
Participant

Hi guys,

I’m new to using Dante so I have few questions… There is a Audinate software version for Mac? I just have to connect Dante card with my laptop ethernet rj45 connector? Is there any min. value for that ethernet connection? What is the recommended multitrack recording software for A&H? I have read that Nuendo for example is most compatible with Yamaha CL…
Also, what Pc/Mac configuration is required for this system to work without problems?
Thank You in advance

2014/06/26 at 3:33 pm #40387

RB
Participant

Behringer x32 has that option and twice more expensive console doesn’t have that option? A bit strange, but hope that it will be developed in further firmware updates…

2014/05/10 at 10:13 am #39690

RB
Participant

After a freeze 2 months ago, I have checked the setup of my console thorowly, going through every single detail that was assinged… Then I unnassigned whole bunch of stuff I don’t use, setup the console for the type of concerts I usually do, and since then I had more than 5 shows, and the console worked without a problem…

2014/03/18 at 11:10 pm #38382

RB
Participant

I get it, and it might be the reason, but the last time I have experienced the freeze, the soundcheck was already over, and one band that came late was on the stage, rehersing a bit, so I didn’t do much since the sound was already prepared basically, just few monitoring corrections. It just wouldn’t mute a dca group, and since it was very near the start of the show, I have quickly unplugged the RJ45 connector, turned the console off and back on, and continued. I didn’t have time to look at the problem. At this point, I have already installed the v1.4 firmware

2014/03/17 at 3:37 pm #38330

RB
Participant

What do You Chris mean by “too much control input”?

2014/03/17 at 11:30 am #38319

RB
Participant

The only logical answer I have read at this GLD forums regarding the freezing issue is that people should be careful about system configuration. By changing the system configuration and removing a certain output type which is assinged to one of the faders or the outputs can cause the console to freeze. Also, it is wise to reboot the console after the configuration changes. Also I avoid using the usb, because any external drive that gets pluged in a computer connected to internet can have a virus or a trojan, or something that can harm the console software.

2014/03/14 at 9:09 am #38257

RB
Participant

Then why it happened to me after the update to v1.4?

2014/03/13 at 5:38 pm #38243

RB
Participant

So You’re saying that if I have a Mono matrix for example at bank 2, D strip assinged, and I go to setup to reconfigure the console and remove all mono matrixes, it could cause a freeze? That seems logical and hope that this is the only problem…

2014/03/12 at 11:14 pm #38228

RB
Participant

Just before that my console froze, so I have unplugged the cat5 cable just to avoid cracks when I turn off the console to reboot. I was just wondering did the QOS error cause the freezing or did the freezing cause the QOS error.
Now I have the answer for the error… Still looking for one for the freezing…

2014/03/12 at 7:10 pm #38220

RB
Participant

Hello stexx,

I have had this problem also, it froze 3 times in 10 months, no matter what firmware was installed, but it happened for the first time 4 months ago. Luckilly, it didn’t happened during a show, so I had time to reboot and start again. I’m trying not to use a flash drive on a console, especially for live recording, and I reboot the console after I change the console configuration.
But I don’t know the exact answer to the problem either.

2014/03/12 at 7:05 pm #38219

RB
Participant

In adition, what is a QOS error?

2014/03/12 at 7:04 pm #38218

RB
Participant

Thank You Antony for Your reply,

that must have been the problem since I have now loaded the template LRM show on my GLD Editor and the Mains to PAFL are set to 0.0db. I have assumed that it is a configuration issue but couldn’t find the reason why. Glad that we have sorted it out.
Since You’re a software manager, can You tell me are there any known reasons for a GLD 80 console to freeze? It happened 3 times to me, in 10 months since I own it, but in all these situations I have had time to reboot and continue to work. The audio works, but the controls don’t respond. It happened few days ago, even after I had updated the latest firmware.
I also see that some guys have had this problem aswell, but noone seems to have the accurate answer.

Regards

2014/03/11 at 10:31 pm #38207

RB
Participant

I just went to my warehouse and tried to find out what went wrong. I have tried loading some older shows and template shows and I did not have that problem. When I tried to load my latest show few days old, I have experienced the same problem again. Then I have just deleted all the shows and created a new one… I don’t know what caused the problem, but it is fixed at the moment, although I would like to know what happened

2014/03/11 at 7:26 pm #38203

RB
Participant

Yes, of course the mix button is pressed. Also the M output meter works fine… this problem occured after the 1.4 firmware upgrade

2014/03/11 at 7:17 pm #38201

RB
Participant

The three strips on top of the console which 2 are ment for main lr output level and input level when pressing pafl button, and one is for mono output level. The lamps.don’t signal the lr output level but the pafl level works and mono output signalisation works also. I can’t see how strong the output signal is on the console
Author

Posts