• Thanks Nicola,

    This morning when we booted up the console Card 3 was not recognized, after cycling the power on the DX32 all was good.

    Slot 4 – Card 4 was an output card. After today we have enough outputs on the DX64 so I swapped, as you suggested, input card 3 into slot 4 and put a blank cover on slot 3. This worked perfectly but we will…[Read more]

  • Thanks Nicola,

    This morning when we booted up the console Card 3 was not recognized, after cycling the power on the DX32 all was good.

    Slot 4 – Card 4 was an output card. After today we have enough outputs on the DX64 so I swapped, as you suggested, input card 3 into slot 4 and put a blank cover on slot 3. This worked perfectly but we will…[Read more]

  • Thanks Nicola,

    This morning when we booted up the console Card 3 was not recognized, after cycling the power on the DX32 all was good.

    Slot 4 – Card 4 was an output card. After today we have enough outputs on the DX64 so I swapped, as you suggested, input card 3 into slot 4 and put a blank cover on slot 3. This worked perfectly but we will…[Read more]

  • Thanks Nicola,

    This morning when we booted up the console Card 3 was not recognized, after cycling the power on the DX32 all was good.

    Slot 4 – Card 4 was an output card. After today we have enough outputs on the DX64 so I swapped, as you suggested, input card 3 into slot 4 and put a blank cover on slot 3. This worked perfectly but we will…[Read more]

  • I’m currently using an S5000, DM64 and a DX32 with 3 analogue input cards in slots 1, 2 & 3 and one analogue output card in slot4. I also have a Dante card mounted in the surface for recording.

    Upon boot up for the first show for some reason the desk did not recognise card 3 and none of the other DX inputs would pass audio, but it appears p…[Read more]

  • PeterM replied to the topic SQ V1.2 in the forum SQ general discussions 1 year, 6 months ago

    Can I use my DX32 with the SQ now? … the notes say DX hub support but there is no mention of DX32 support … ?

  • ddff – the SQ will connect to the DX32, but its not stable at the moment. I have tested it over many days and eventually it will disconnect.

    I believe firmware 1.2 will fix this issue … hopefully soon.

    Peter

  • “I think he is missing a configureable output of the PAFL. At the moment you can only listen to PAFL via the headphone output. It would be nice to have the opportunity to route the PAFL to any output socket.”

    Especially if you want to use it as a monitor desk etc.

  • Thanks Nicola,

    It was my original understanding, that the DX32 was not supported with the first firmware release, but would be with the next release, then there was release 1.1 so I thought great; it’s here earlier than expected and tried to the connect the DX32 – it immediately recognised all the channels and worked perfectly.

    I ran it for…[Read more]

  • Thanks guys – my concern is that the cable I was using was one recommended by A&H http://support.allen-heath.com/Knowledgebase/Article/View/367/0/recommended-cables
    … so is there an issue with the SQ6 and its connection to the DX32 or do I just need a higher spec cable?

    At the moment we are substituting our dLive or iLive where ever possible…[Read more]

  • PeterM started the topic SQ with DX32 in the forum SQ with DX32 1 year, 8 months ago

    SQ6 with DX32 (24+8) seems to work perfectly. Tested it for two day before we tried a show (with a short Cat5e cable).

    It ran for about 5 hours during sound check perfectly, but 3 songs into the concert it disconnected. Plugging the cat5 in and out it fixed the problem for a short time.

    It appeared to be a communication issue and I suspect it…[Read more]

  • SQ6 with DX32 (24+8) seems to work perfectly. Tested it for two day before we tried a show (with a short Cat5e cable).

    It ran for about 5 hours during sound check perfectly, but 3 songs into the concert it disconnected. Plugging the cat5 in and out it fixed the problem for a short time.

    It appeared to be a communication issue and I suspect it…[Read more]

  • SQ6 with DX32 (24+8) seems to work perfectly. Tested it for two day before we tried a show (with a short Cat5e cable).

    It ran for about 5 hours during sound check perfectly, but 3 songs into the concert it disconnected. Plugging the cat5 in and out it fixed the problem for a short time.

    It appeared to be a communication issue and I suspect it…[Read more]

  • Thanks Nicola,

    I expected that I would not be able use the DM rack … but maybe … if you were going to be able to control the preamps in the DX32 racks it may have been possible with the DM via the DX port.

    We have iLive, dlive and Qu in our inventory as well DX32 and AR2412 racks. Often the Qu24 has enough inputs for many of our shows and…[Read more]

  • Three questions –
    • Can I use the SQ with my DM64 rack without a Dlive surface when I need to save space?
    • When can I expect support for my DX32 rack?
    • Does the EFX’s include a dynamic EQ?
    PS looks fantastic and I have ordered a couple 🙂

  • I really miss this function – While I don’t think a mixing desk should be the crossover/ processor for the main speaker system, it was so handy for so many things.

    – small shows to mix and match different subs and mains and time align them as necessary
    – theatre shows to integrate the various speakers – front fill, stage effects etc.
    – large s…[Read more]

  • Just make the D-esser a fully functioning Dyn. EQ. For most applications that would be perfect.

  • another +1 … I have some iLives and a Midas, the pop funtion is great …