Forum Replies Created
-
AuthorPosts
-
2020/09/19 at 8:00 am #95039
@mikec Yes i tried it pressing the on screen button but the same happened. I have selected from presets a vocal delay.
@SteffenR The red button flashing is “in sync” with the yellow dots on the screen that also flashing but also both are out the beat. You probably mean that the short delay for the time calculation is the issue. So there is no way to achieve tap delay exactly on the beat?
Thanks!
2020/09/18 at 3:15 pm #95025@mikec yes i am tapping 4 to 6 times exactly on tempo because i am a musician too but its still out of sync. This is very strange
2020/09/18 at 1:44 pm #95022@giga I am pressing the button i don’t understand what do you mean with “tapping” the button. Is there another way?
@markpaman On a live gig i don’t know exactly the tempo the band plays that moment, so i want with tapping the softkey to match exactly the dalay time. For example i don’t know if the song is 118 or 120 or 125 bpm thats why i am asking!
Thanks for your replies!
2020/09/18 at 3:59 am #95012Sorry this is the correct link!
2018/10/29 at 7:32 pm #79631Hello Alex thanks for your answer!
I want to split input channels and to apply different eq, compressors, reverbs etc to send to ME-1’s. My thought was to do the “monitor” job from qu and send it to ME’s and keep SQ independently for FOH.
Thanks
2018/04/01 at 5:48 pm #70017Thanks GCumbee but if i decide to go with ME’s then probably stay with my Qu16.
Another concern is that with stereo mixes i have compressor/eq etc per stereo mix but with ME’s i will have only individual channels.Thanks
2018/01/02 at 4:10 pm #67851@dick rees
Thank you very very much i understand the way you “pan” and i will try it!
Althought the “link” feature of mono mixes to stereo is essential for me and as a have seen is a request of many users of Qu family but unfortunatelly no response from A&H
Thank you again!2018/01/02 at 12:24 pm #67823Thanks a lot! What about Y cables and phantom power in my first post?
2018/01/02 at 12:20 pm #67821Thanks again Dick Rees but with this way i have no panning or am i wrong?
2018/01/02 at 11:55 am #67815Can you explain how to do this? Thank’s for your help!
I want to have 5 stereo mixes instead of 3, for wired IEM’s with panning etc.2018/01/02 at 11:50 am #67812Dick Rees, sorry my fault i want to link mono out’s to stereo and not channels
2018/01/02 at 10:54 am #67809Thank you Lee7 for your reply!
I want to avoid active/passive mic splitters as it’s extra gear with extra cost, cables etc.
Surely your solution is much better than Y cables, but i want a simpler setup.
I use one mixer (qu16) both as FOH and monitor as i don’t need more channels. I just unassign “monitor” channels from FOH (LR) and that’s it. (i’m using wired IEM’s)
I don’t like either X32 app is very frustrating.
The only thing i wish from “Santa Clause” 🙂 is the feature to link mono channels to stereo but A&H probably stops the updates to QU family.Regards
2017/05/04 at 7:33 am #63196Bob althought there has been no “end of support” announcement, it’s a little bit disapointing the fact that almost a year now there is no further “development” of the mixer.
2017/05/04 at 6:33 am #63193Thank you ddff_ly for your answer. Maybe I’ll some external FX as you mentioned before.
2017/04/08 at 10:34 am #62762Any help?
Sent from my iPhone using Tapatalk
-
AuthorPosts