[DartParticipant]

And if we don’t have group outputs, is there any possibilities to switch the monitor 1 and 2 in a stereo monitor out?
We work with 5 IEM and 3 musicians get a mono signal on stereo IEM. It’s really problematic…

[DartParticipant]

Just a minute…

When I clic on the rec button (passing the rec mode on “pause”), the channels 17/18 are ok!!!

If record is not armed, then I don’t see the ST in.

Strange but it seems to work!

THANK YOU VERY MUCH KEITH !!!

[DartParticipant]

I made everything you suggest Keith but I slowly think something doesn’t work well, especially with the I/O patch…

I explain : if I send in the I/O USB patch the mic source (the mic is plugged in the input 1), to the channel 2 or 3 (even simultaneously, it’s possible), then the mic always appears on channel 1 !!! Due to the routing, it should then appear on channel 2, 3, (…) of my multitrack recording. It’s very strange.

Nothing has an effect on the routing of the tracks in the multitrack recording pannel.

Track 1 is routed to channel 1, 2 on 2, …

It’s like is the I/O usb patch didn’t work.

[DartParticipant]

So, I just plug my iphone in the ST in 1.

Then I selected « direct outs » in the I/O usb patch… And I chose « post preamp » in the direct out preamp section of the individual tracks.

Finally I plugged an USB key in the Qu-SB and checked the multitrack Panel with a mic on channel 1.

The result is not what I expected : nothing on 17-18 tracks. But I get the sound of my mic on channel 1 and see the meter of ST in 1 moving in the main inputs panel.

Attachments:

You must be logged in to view attached files.

[DartParticipant]

We go on talking about it here okay? This is your your more detailed answer. Thank you again for your help Keith!

English is not my basic language so I have to translate a little your technical answer.

If I understand well, you advise me to work in “direct outs” mode and to take the source of any track just after the preamp, right? (post preamp to be correct) ?

In this case, I will be able to assign the stereo in 1 from the Qu-Sb to the 17/18 channels of my multitrack recording, that right?

[DartParticipant]

Impossible to delete my multiple post on the same subject Keith. If you can do it for me, no problem.

Thank you again. I will now check if your tip gives me satisfaction.

[DartParticipant]

I work with a QU-SB and when I assign something to tracks 17-18 in the I/O patch USB I don’t have anything on these tracks in a multitrack recording… It’s a big problem to me who work with 18 tracks all the time!

I don’t work with a DAW in live recording. Only through a SSD disk drive.

If someone could help, it would be great!

I read the forums, the manual, everything I can but it’s very hard to find a tip to do so.

[DartParticipant]

This week end I made a multitrack recording with my band during the shooting of a videoclip.

When I assigned the ST in 1 to tracks 17/18 in the USB I/O patch, I got nothing at all! Is it normal?

[DartParticipant]

Hello I am working with Qu-Sb and do sometimes multitrack recording.
Qu Drive allows to record 18 tracks but these tracks are 16 + 17/18 that correspond to the LR, right?
If I assign in the I/O patch USB my ST in 1 to the track 17/18, I don’t have my ST in 1 in my multitrack files…
Is there a tip to really record 18 TRACKS WITHOUT THE LR ?
It’s really important for me to do so. With my band we use the 16 XLR inputs + the ST in 1 in live and rehearsals…
Thank you.

[Author]

Posts