Forum Replies Created
-
AuthorPosts
-
2020/04/11 at 6:45 pm #90932
Thanks, BRS. I hadn’t accidentally hit the “on” button on the channel?
2020/04/07 at 9:26 pm #90839Hi Mike. Thanks. Indeed I have tried hard reset (unplugging), and several Network/Factory rests, which are often dysfunctional: lights do not always signal after reset button is pressed.
It occurred to me to try a firmware reinstall but once I asserted that weeks ago I had already installed the latest firmware, I assumed that firmware wasn’t the problem, but… now that you suspect that it could be, i’ll see that through ….stay tuned….2020/04/07 at 1:06 am #90810attached is an mp3 of the noise emitted from the Qu-SB that preceded is current behaviour of randomly ceasing audio (i.e., monitoring audio)
Attachments:
You must be logged in to view attached files.2020/04/07 at 1:02 am #90809I am very grateful for your attention. Thanks.
Yes, when I open the QU-Pad mix APP, the QU-SB is an option. I choose it, *plus* does not appear to disconnect.
On the router it’s plugged into one of the LAN ports, yes.
On the mixer the plug is indeed into the network jack, not the dSnake jack.2020/04/07 at 12:36 am #90806Thank you Mike C., but my iPad is connected, plus to clear, upon further testing I discover that leaving the studio overnight “heals” everything back to functional …until… a static “pop” kills -either- the sound and its corresponding lights that are active in Qu-Pad -or- only the sound: perhaps the first time that this happened, Qu-Pad lights will still actively reacting.
It’s as if the Qu-SB becomes to hot after several minutes, (it’s not) then mutes itself after an electrical “pop”.
I hope to hear back from USA Tech Support tomorrow. This will not do.
Thanks , again!2020/04/07 at 12:27 am #90805Thanks, Giga, but my iPad is connected via WiFi router and CAT5 to the Qu-16 Network. I also do not witness any disconnection.
2020/03/30 at 12:48 am #90591Yes, I thought that’s the pre-amp, just isn’t labelled as “pre-amp”, so I wasn’t sure if I had elsewhere to search.
Insert is gray; toggle’s on “FX”
thanks2020/03/30 at 12:37 am #90589Hi Mike. Thanks, that’s an excellent question, as I am not clear what the pre-amp screen is; I’m aware of how to navigate each channel’s processing, but in that area, pre-amp is not apparent.
2020/03/30 at 12:10 am #90586Hi Mikie, thanks. Yes, I tried ch.14 also, plus swapped in a dynamic, to no avail. No surprise that PFL (assuming that is what PAFL is in this land) yields no sound in headphones, and no lights in Qu-Pad.
Thanks for clarifying the USB B; I was going to submit a seperate thread on this but, I’ll jot it here: I also lost my ability to playback audio from Logic. I was using ch.31-32, assigned it out in Logic prefs, see Logic’s stereo out lighting with playback, but zilch signal through Qu-Pad, when I had that hours ago as well.2020/03/29 at 11:47 pm #90582thanks Steffen R. Ch.16 input source is “Local” (red) and USB B (blue). My understanding is that “local” identifies my Qu-SB XLR in on that channel and “USB B” …<-the out to my iMac?
2020/03/29 at 11:37 pm #90579Thanks BRS. No, I checked that. Even if I hadn’t, wouldn’t the channel react to signal coming in? …and for the record, I swapped out the mic, then the cable, so to rule those out…
-
AuthorPosts