Forum Replies Created
-
AuthorPosts
-
2023/02/21 at 6:02 am #111654
Hello,
Where is the USB key ?
Many Thanks ;-).Press and hold the USB and HPF In keys whilst powering on the unit. It will then show this same behaviour and, if it loads the firmware successfully, it should eventually boot.
2017/11/07 at 1:58 pm #66174Mmm … , Multitasking at Tablet forbidden to use the app😳, a feature Request for the App ?
2017/10/26 at 10:31 am #65888Thanks, I will take a try 😊.
Any other suggestions, why the open app loses the link to the console when I successfully logged in?
Thanks friends
Micha2017/03/20 at 6:03 am #62240Hi all,
I have the problem with sometime losing connection of QU-PAD too. Every time I record the session to USB Stick, connected via USB Cable.
My WLAN Router (is standing directly under and inside the QU-16 at the right side (near USB stick – connected via USB cable to QU-16 USB Port) – Only the antenna is outside the QU-16.
Now I change the routers place to the left and under the QU-16 and no connection loss, Problem are interferences USB – WLAN ??
I will take a try in the future and at live sessions too.
Kind regards
Michael2017/01/10 at 2:04 pm #60476Best thanks for the answer, the corrupt wav’s I have unfortunately cleared, but for the next time I have with the VLC an option.
Kind regards Micha2016/10/26 at 1:06 pm #58885Dpd an and Lou, thanks and You are both right, all concerns and explanations are authorized and I am aware and also aware and if possible, we also book a mixing man. In the meantime, however, I have also mixed some of our performances (have to mix) and would like to know about my concerns regarding QU-16 in this forum contribution.
Many thanks and greetings from Germany
Micha2016/10/26 at 4:26 am #58873My problem is the input gain leveling at the vocal mic’s. We have 4 vocals and the input level at step “2” is not the same as in step “4”. And now in step “5” I have to set the final level of the vocal mics, but without the real vocal, I have to use the playback only …
2016/10/21 at 4:52 am #58766I use the the Multitrack recording feature for thi too, I’m the front man and the mixer man in the same person 😜.
I use 2 stereo recordet songs from USB device for adjusting PA.
After that I play a Multitrack recording from the last show to set up a basic mix. Setup a raw monitor mix.
Change input from USB to local, set up gain of all channels , start Multitrack recording and start soundcheck with take band.
Our Backline isn’t loud – E-drum 👍 So I can setup up the monitors and the front sound with the Multitrack recording after Soundcheck with one ore two songs quickly.
I set the gain of all USB channels to 0db and leave it so. The problem at self made Soundcheck ist to correct the gain of a channel. Do not change the gain of correspondence USB channel. It will works to correct the mix at Multitrack playback only, you must correct the gain of the local channel, but you can’t hear the change at Multitrack playback – is a little bit tricky 😏
But I have the feeling that the playback level is less in the multitrack playback (usb gain level set to 0db) than in the recording – can someone help to correct this?
Regards Micha2016/05/20 at 11:31 am #55922Hi bob, nice idea, but it’s to “hot” 😜
2016/05/19 at 1:09 pm #55890Thanks all, And yes I look for a Solo one Channel at Main out And mute all Other in one step (Soundcheck with / without USB Play-back (I’m the Frontmann of out Band And the FoH too 😀😭). But it isn’t a Problem, if theres not a Solution.
Micha2016/05/19 at 9:59 am #55883Yes, i know the manual ;-),
Sorry, I have certainly described not entirely correct, what function I’m looking at the qu-16th Is there a way to switch a channel solo on Main Out, without any other active channels to mute ago -
AuthorPosts