Forum Replies Created
-
AuthorPosts
-
2023/04/29 at 7:18 pm #112641
Hi,
In my case , after 8 Years , there as no problem with my GLD 80 , the Repair provided by A&H was good ^^.
in my case the issue was resolved by replacing : the internal wire between motherboard .2015/05/29 at 1:12 am #48353hello
I sent my 80 GLD in my usual professional repairer, and he will take over the operation.I expect afterwards.
2015/05/19 at 8:48 pm #481412015/05/19 at 8:38 pm #48139@ Allen & Heath
I send you, logs still in my possession, and a picture of the screen when the GLD Frezze, Saturday, May 16, 2015.
hoping you have a solution for me.
Thank you
@ Tylermartin86,
I do not use MIDI, and I do not think I activated commands.
For the keyboard: I plugged in to access BIOS in my workshop. in concert, it is not connected.
For the connection, I had forgotten to turn on the AR2412 !!! but after it has been unplugged.
The Digital Snake is new and was in the first things checked. it is ok.
I do not think that the problem comes from the AR2412, because the sound was working without worry during Frezze.
for show, after the last rebooting, La GLD80 were Lags, and would not rebooted the show. in an emergency, I have found a solution, because I found my most Cle usb. (Panic …) with my memory, I loaded an old show, for the show restarts.
ansuite, I took out my computer, and I took a backup (300315 0MAC 1) I had in the GLD EDITOR, and I charged during a break.
I never used to show from a GLD112.
anyway thank you for the help.
2015/05/18 at 10:41 pm #48118Tylermartin86
I sent you my logs, hoping you find a problem, and a solution
thank you for your help.
2015/05/17 at 11:40 pm #48076Thank you for the tip John-S,
Today I looked and study all diagnostic LOG connected keyboard and accessing the BIOS (F2)
The bios is not at the same hour as the interface
in the diagnostic log the bios, I saw this error: EFI 01010003
(The date and time corresponds to a Frezze each time)Aptio Setup Utility: Version 2.11.2110
BIOS information:
BIOS Revision R1.13.0CD
built Date and Time 01/24/2012
Board D3003-S12I touched the screen during the boot of the console, 2 crashes, otherwise just started can long (47 s on average) test performed 12 times.
I have no iPad to try.
PS: in the last Frezze, no USB key was connected.
serial number: GLD080X-323863
looking more closely the effects, I saw that the person using the console loaded 4 times the same effect: HALL480 (with 4 different tuning of parameter) on 6 used ,
is that this could be the beginning of a solution?
2015/05/17 at 4:30 am #48045Hello everyone. it’s me again.
My GLD80 freeze again, and it was during a big concert, it’s always the same message:
/ Dev / ah_usb_dsp – Flush failed
I do not know what to do, the hammer is not far away so this problem annoys me !!!
how much would cost the exchange of the mother card, and DSP?
unless someone has a solution for me.
My importer: audiopole, ” does not seem very motivated” when I was told that I had bought second-hand console.
2015/03/30 at 1:15 pm #46382Apparently, the console was purchased in April 2013 by the company that sold it to me.
I use a USB Key for back-up : Shows and Scenes.
I used too, to 10 music I used to check the system.
that’s all.at each freeze, the USB key, blinking abnormally, although I did not read music and I did not record.
the USB was plugged in, but no action was writing or reading in progress normally.On your advice, I’ll contacted my distributor in France: Audiopole .
2015/03/29 at 9:54 pm #46341the console was purchased two months ago, in a company which changed its equipment.
the console worked very well, and now she freeze.but every time it freezes, USB drive was plugged into the console.
Why does this matter?
2015/03/29 at 7:16 pm #46336My GLD 80 :
Firmware : V1.42- Rev 15810
Surface board driver : Version 1.1
DSP Board driver : Version 1.3
Motor fader driver : Version 1.1
Help set : v1.41
Operating system : v3.00 -
AuthorPosts