Forum Replies Created
-
AuthorPosts
-
2010/11/15 at 4:56 am #26775
Dutch owners club … as long as it’s not in Dutch!
2010/11/06 at 11:50 am #267182010/11/05 at 7:58 am #26712Seek and ye shall find!
Fantastic … thanks, Dave!
I’m presuming that these truly work as filters, with no ‘slope’ on the cut-off? I’ll be able to analyse that once the system is hooked up, but I’m pre-configuring before installing.
Thanks, once again …
Guy
2010/11/04 at 10:04 am #26704Many thanks, Sam.
2010/11/02 at 11:12 pm #26697Might be a stupid question, but will the new Dante card stop the use of the DIG OUT?
2010/10/12 at 1:51 am #26615I couldn’t find the Yamaha app … Certainly not under ‘Yamaha’ or ‘StageMix’ in the app store … Do you have a link, John?
2010/10/11 at 5:23 pm #26608It would be good to see which other users are online at any given time. I don’t know if there is an interface to the ‘server / router’ function through HTML, but I certainly haven’t found it (and I’ve tried.)
G
2010/10/08 at 11:44 pm #26598I know it’s super lazy of me, but I would like to see the ‘libraries’ a little fuller. If I’m doing a quick mix, it would be useful to be able to pull some ‘safe’ compressors, gates, EQs, etc. for toms, voices, basses and the like. Our LS9 is stuffed full of that kind of thing, and, in tight spots, I find it useful.
2010/10/07 at 11:28 am #26594I had a demo of it yesterday, and it works really well! Very intuitive, fully-featured …
However, there are still quite a few missing bits, so I guess it’s going to be weeks, rather than days … But I guess the A&H guys will answer you more precisely!
Guy
2010/10/07 at 10:39 am #26593Frank: I mean that when I’m going from Utrecht Centraal to Nieuwegein, I need to change from number 77 to … )
No, I mean any change in the routing in the mixer: for example, you might re-balance the number of Mono and Stereo Aux’s. Another ‘BUS’ change (at least in my eyes) would be re-allocating the physical outputs from one source to another.
Guy
2010/10/06 at 4:23 pm #26586Thanks for your help, Andy.
Our new IDR is happily installed at home for set-up and testing, and I have no problems accessing it via the routers and switches, from behind our firewall / modem.
AND … wonder of wonders! … I can access the IDR from iTweak over the net!
It took some fiddling, because it was difficult to establish whether the ports were open and indeed whether the IP address was even accessible, as my ISP doesn’t allow pinging or port scanning, funnily enough …
Things to note:
1. It takes time for the iTweak to ‘find’ the IDR over the net, so be patient: give it a minute or so before starting over.
2. The ‘delay’ in producing an effect on the IDR varies: if you haven’t done anything for a while, the connection seems to ‘sleep’, and then wake up. The delay seems to be around 0.3secs, which would be quite close to the ping return time I would think, and it’s absolutely acceptable in a set-up like this.
3. Flattening EQ’s seems to do a double-take: it only seems to work on the second attempt: this might be my inexperience with iTweak.
4. The DYNDNS service seems to be free, and it works instantaneously.Other than that, this whole process gave me wood, and will save me a lot of time, driving up and down the motorway to fix small mix problems in clubs …
Great job, A&H!
(Now, please kick Dante into gear! )
Guy
2010/10/05 at 9:45 am #26575Hi all,
Yes, this all makes sense. We’ll set it up next week … And I’ll report back!
-
AuthorPosts