Forum Replies Created
-
AuthorPosts
-
2018/04/03 at 3:54 am #70053
“Ok, changing channel 1 to Bobs Mike”
2018/03/19 at 7:37 pm #69750Yes I switched it from 44.1khz to 44khz and it works well.
2018/03/19 at 7:20 pm #69748Yes, I have put my EFX on the “Soft Rotaries” and so I see the name of the EFX but turning the knob I have no idea how much I have changed the db of that effect. So please have it display the db when turning the knob.
2018/03/19 at 7:16 pm #69745Yes we have used two iPads at once. I believe I was told (at least with v1.1) that more than one iPad at a time is not supported yet, so if something happens, its not the software’s fault.
2018/03/12 at 7:14 pm #69534I agree.
Or at least being able to change the patch on each channel. If I’m on stage trying to troubleshoot a problem, it would be helpful to just use the app to change the patch right there to confirm it works rather than having to walk back to the booth to change it.
2018/03/12 at 3:51 pm #69523V1.2.0
Additional Features:
D-Classic Automatic Mic Mixing added. Support for DX-Hub.
‘Chorus’ and ‘Noo Phaser’ FX units added. Assignable Channel Colours.
Factory Processing Libraries added.
Input to PAFL source point selection added.
Improvements:
ID-839: Fix UDP port numbers to allow port forwarding.
ID-784: Match Frequency and Width values on PEQ screen to hardware.
ID-739: Add categories to FX Library.
ID-447: Enable selection of ‘Processing’ or ‘Routing’ screen key before selecting channel.
Issues fixed:
ID-852: Channel settings recalled incorrectly when changing channel stereo status ID-812: Stereo width changes can cause issues when switching channels back to mono ID-804: AR/AB units can dropout or enter update mode
ID-803: Static IP settings not updating correctly
ID-723: Changing gate sidechain source from ‘self’ on SLink input channel mutes audio ID-726: Selecting PAFL on SQ-MixPad changes ‘Sel’ on surface
ID-721: ‘PAFL Follow Mix’ does not work in ‘Fader Flip’ mode
ID-468: Master fader does not update when level changed on SoftRotary
ID-437: Next scene does not update after scene name change
ID-634: Surface can freeze with bad connection to SQ-MixPad app2018/03/07 at 6:24 pm #69431It is a Macbook Pro, so it has the SSD. I will check on the 48 vs 96 in Logic.
Thanks
2018/03/05 at 7:34 pm #69370Hi A-Moll,
I’ve just tried recording via the USB rear output on my SQ6 and using Logic Pro X on a nice macbook too. I keep getting the Disk speed not fast enough (write) error and it stops the recording too. Have you found anything that will make it work? We were wondering if it is because the console is 96khz.
Thanks
2018/02/19 at 7:25 pm #69034Hi GC,
If I do the proper SQ6 shutdown procedure before activating the sequencer, there will be a loud pop since the amps/speakers are still on?
2018/02/19 at 5:22 pm #69029Yes, Lightingman, I come from the IT world, so I like to properly shutdown computers via the GUI (unless theres a problem of course). So I would assume that is the best and safest way to shutdown the SQ6. But this is my first non-analog board, so I could be wrong.
Thanks
2018/02/19 at 4:26 pm #69025Would that be enough time to do a proper shutdown before the sequencer kills the power, without being too early to cut the signal to the amps/speakers? Or are you just killing the power without doing the SQ6 shutdown procedure?
-
AuthorPosts