Forum Replies Created

Viewing 15 posts - 1 through 15 (of 35 total)
  • Author
    Posts
  • #104028
    Profile photo of Phill
    Phill
    Participant

    I see 4 channel gain changes…KEys TTCan TTRab Aux mic
    however if you are referring to TT Can & TTRab You Have AMM on those channels… I don’t use AMM myself but expect that could be the issue, someone will be able to chip in on the AMM tho

    #103180
    Profile photo of Phill
    Phill
    Participant

    If you leave it for a few min does it eventually boot up?
    I’ve got one that if left for days without power can take 2 min before you see the run of blue lights to boot..

    #88629
    Profile photo of Phill
    Phill
    Participant

    Thanks Keith, brain hadn’t got that far yet all clear now 👍

    #88626
    Profile photo of Phill
    Phill
    Participant

    hmm… ok so excuse the “idiot” question it may not be 100% relevant however if i’m running SQ5/6 with 3 DT168 all at 96K and have 48ch to record.. the means I can’t sync the DVS I have to set it up on 32ch only? or will it just drop down to 48k?

    #85693
    Profile photo of Phill
    Phill
    Participant

    I have/had tickets/RMAs – Sent a PM

    #85676
    Profile photo of Phill
    Phill
    Participant

    Hi Alex,
    I did however having to try return through distribution failed somewhat and it was never sorted out.. their communication skills were far from primary school level, considering the size of them..
    Not an A&H issue, however just a poor agent service… mines out of warranty now even though the ticket was raised while in warranty..

    #85668
    Profile photo of Phill
    Phill
    Participant

    I’ve had really slow boot issues after I leave it a couple of days… it just take for ever to boot up after that, if it’s out every day fine but otherwise mine can take 90sec to even get to the blue light run, if it doesn’t want to boot then I turn off n on and it’s straight up and running again…
    I’ve also had all the lights flash on n off several times at boot…
    Desk seams rock solid once it’s up n running tho..

    #84062
    Profile photo of Phill
    Phill
    Participant

    HAPPY DAYS !!!!!!!

    Thanks guys !!

    #83987
    Profile photo of Phill
    Phill
    Participant

    Almost given up hope… really hope it’s rock solid or I may just hide in a corner…

    #80790
    Profile photo of Phill
    Phill
    Participant

    I had a similar thing yesterday, first time on 1.3 (not using 1.3.1 yet)
    I was running externally on the DX168 and went to put phantom on a pile of condensers. The phantom power button pad etc was greyed out for some reason and I was a little panicked at the time being honest… I checked my input selection and was on slink. I tried just pressing and holding regardless and it didn’t select.. I went threw a few pages to see if the selection had moved or I had missed something nope… came back and it was no longer greyed out and I held n it selected in and worked no probs…

    #78395
    Profile photo of Phill
    Phill
    Participant

    when will it actually available from uk distribution…

    #73470
    Profile photo of Phill
    Phill
    Participant

    Ok so for clarity as I realise I was rather less than specific….
    SQ6 into 2 cascaded DX168

    🙂

    #72949
    Profile photo of Phill
    Phill
    Participant

    Awesome!
    Do we have gain compensation ability yet or are we limited to one console adjusting gain while the other uses digital trim so it’s all manual…?

    #72851
    Profile photo of Phill
    Phill
    Participant

    So just putting it out there… does this mean I can use my 2 dx168 in on slink port on one desk and send inputs to 2nd desk via Dante allowing me to do foh & mons now instead of waiting for the slink card???

    #71871
    Profile photo of Phill
    Phill
    Participant

    I can’t see why there would be any issues….

Viewing 15 posts - 1 through 15 (of 35 total)