Forum Replies Created

Viewing 15 posts - 1 through 15 (of 45 total)
  • Author
    Posts
  • #79633
    Profile photo of Creator
    Creator
    Participant

    Yes the camera is hooked up to the alt out as is the external speakers to feed another area. They are currently both hooked to alt out via a splitter. That’s why I was wondering if I can just use the cable I posted as it would be the cheapest route and we don’t have a huge budget. And if things change how we are doing video I don’t want to spend a lot now and have to maybe do something different later

    #79623
    Profile photo of Creator
    Creator
    Participant

    The camera is a basic hd camera I think it is sony. It has a 3.5mm mic input and headphone jack for connections

    #79618
    Profile photo of Creator
    Creator
    Participant

    Because I use it to feed some wireless speakers. The matrix feed I have set up is a boosted LR signal.

    #79608
    Profile photo of Creator
    Creator
    Participant

    I want to take the matrix signal from the board and send it to our camera. Since the board sends a line level and the camera takes a mic level signal it’s really hot and there isn’t a lot I can do in between to change that. I was looking at this Movo MV-RC100 3.5mm Male Line-in to Male Microphone Attenuator Cable for HDSLR Cameras https://www.amazon.com/dp/B01GW69IQ2/ref=cm_sw_r_cp_apa_ZQL1BbSJCF89X

    #70558
    Profile photo of Creator
    Creator
    Participant

    Currently using the alt out for a wireless speaker system in the basement. So I thought about using the 2trk out for the camera or as we did this week used a splitter on the alt out and ran the wireless speakers and the camera from one but they both really need different levels so that’s why I was asking about aes not the 2trk out will have to work just need another cable and to convince the pastor to spend the money on that mic camera adapter, which thank you for the link as well.

    #55567
    Profile photo of Creator
    Creator
    Participant

    Sorry I sent this from my phone, that first line should read the channel profiles.

    #53423
    Profile photo of Creator
    Creator
    Participant

    So trying to record on sunday, I ran into the same issue I was having before. I had to format the drive with a computer then reformat with the board for it to work. We never had to do this before. Not sure what the issue is but we at least got it to work. One other question I was trying to record with audacity as it is a free and pretty decent program. The problem I had was it only recorded the 1st channel on the board which for us was bass. Any help in trying to record using the usb B output to pc would be great.

    #53272
    Profile photo of Creator
    Creator
    Participant

    After installing 1.82 again, I had the same success as when I was back on 1.73. Not sure if it was a firmware problem, but I also reformatted the flash drive with my computer then reformatted with the board as well. Hopefully when we go to use it this week for service it goes well.

    #53264
    Profile photo of Creator
    Creator
    Participant

    So after rolling back to 1.73 I plugged my phone in to the ST3 port to record and was able to record for about 20 mins until I stopped it. Installing 1.82 again to see if It will do the same. I will report back with any Issues Typically it records for about 30 secs or less until it stops on it’s own.

    #53227
    Profile photo of Creator
    Creator
    Participant

    I’m not near the one we use right now since I’m at work. I
    am going to look at it today or tomorrow.

    #53218
    Profile photo of Creator
    Creator
    Participant

    How do you reinstall the same version of firmware? From my experience it won’t install the same version as what is already on the mixer. Do I just install an old version then reinstall the 1.82?

    #51486
    Profile photo of Creator
    Creator
    Participant

    IS it possible to add support for Aviom in ear monitors for the qu series mixers or is that going to stay on the GL and Ilive series boards only?

    #51466
    Profile photo of Creator
    Creator
    Participant

    We are looking to eliminate stage monitors. This is what we currently use http://mackie.com/products/dlm-series

    Just trying to clean up cabling among getting rid of the stage volume. Plus the people on stage would like them as well since a couple of them have a hard time hearing the floor monitors.

    #51459
    Profile photo of Creator
    Creator
    Participant

    That runs 3900 USD or 2521 gbp

    #51458
    Profile photo of Creator
    Creator
    Participant

    My thought was get 3 of the sennheisers I posted, that would give me 6 packs for musicians and vocals and since we don’t run stereo anyway I can just run them mono.

Viewing 15 posts - 1 through 15 (of 45 total)