I use only one switch Aruba 2930 on FOH ( near DM32 bridge dante card to network1 and AP Aruba305 to network2 for wifi and redundancy).

When i connect IP8 to port POE (default), IP8 said its under powered. When i set port to 30W – answer was same. When i set to 35W, IP8 start, work fine (from statistics: Pwr reserved 30W, Pwr Draw 4,1W, Priority…[Read more]

Hi Wolfgang

You can do it easier – with bridging network

+1

upgrade your mixrack to 1.61 -> webUI (I_Explorer) on PC -> get your Mixrack Ip adress 192.168.1.70 -> update firmware

In 1.52,
when you move I/O grid with mouse pointer, window will always refresh to position 0.0

I use finger to move on grid with touchscreen.

Patching is then OK with mouse or finger.

Hi,

It is better, when you write in one forum post.

Here is debate on it and moore: http://community.allen-heath.com/forums/topic/io-scrolling-in-director-mac

+1

Hello Jay,

Your solution in point 2 with 4 switches i made a scheme and want to ask if i understand it correctly.

Thanks

Hello

Do you have any trick to set IP 8 in director sel or mix, etc.

For example :
When i choose channel 28 and change function from pafl to sel, it will automatically reset the channel to 1 and change input to DCA.
Then i have hard to change on touchscreen/mouse channel 1 to channel 28. When i change DCA back to input, channel will again reset…[Read more]

Hello

Do you have any trick to set IP 8 in director sel or mix, etc.

For example :
When i choose channel 28 and change function from pafl to sel, it will automatically reset the channel to 1 and change input to DCA.
Then i have hard to change on touchscreen/mouse channel 1 to channel 28. When i change DCA back to input channel will again reset…[Read more]

Hello

Do you have any trick to set IP 8 in director sel or mix, etc.

For example :
When i choose channel 28 and change function from pafl to sel, it will automatically reset the channel to 1 and change input to DCA.
Then i have hard to change on touchscreen/mouse channel 1 to channel 28. When i change DCA back to input channel will again reset…[Read more]

Hi Albin

Do you have any trick to set IP 8 in director sel or mix, etc.

For example :
When i choose channel 28 and change function from pafl to sel, it will automatically reset the channel to 1 and change input to DCA.
Then i have hard to change on touchscreen/mouse channel 1 to channel 28. When i change DCA back to input channel will again…[Read more]

Hello

On audinate website https://www.audinate.com/products/manufacturer-products/dante-brooklyn-ii
There is information that brooklyn 2 chip have :
Sample Rates : 44.1 / 48/88.2 / 96 / 176.4 / 192kHz

Audio Channels In/Out (44.1/48kHz) Up to 64×64 channels
Audio Channels In/Out (88.2/96kHz) Up to 32×32 channels
Audio Channels In/Out (1…[Read more]

I have provisionally solution – with the mouse roll wheel only zoom in/out (not click and drag), with the finger moving screen for position and then double tap with finger on screen or click with mouse to patch/unpatch.

I have provisionally solution – with the mouse roll wheel only zoom in/out (not klick and drag), with the finger moving screen for position and then double tap with finger on screen or click with mouse to patch/unpatch.

In ver 1.50 i had another resolution problem:

Dlive Director 1.5 windowed mode – I/O window

In 1.51 is this resolved

1.51

For patching i must switch windowed mode off, then it have better patching

When i touch screen with finger it didnt work and i had to use trackball.

After, windowed mode again on

PC is NUC i7, 2x touch screen Dell S2240T

In windowed mode and win10 (2 touchscren) is some big problem with scrooliong and finding position for patch.

I meant – it is resolution problem ( i use 1920×1080)

Thanks both of you.

I was looking for solution to make both network MR for working with safe connection.
If one connection stopped working i would use the second one on MR.
I know the solution that Tor was writing about trunking network. In this solution there is on one side one cable between PC and switch 1 and 2 and more cable between each…[Read more]

Thanks for replay