[BWhiteParticipant]

Can you assign a library I/O “scene” to a sofykey. For like switching back and forth for a live sound and virtual sound check. One patch scenario is saved as a live service and another patch scenario with USB for virtual sound check. That one button will change it to “live” and another to “Sound Check”. Just trying to save some steps.

[BWhiteParticipant]

Right now the IEMs are setup has mono. We have six shure PSm300. Once everyone gets comfortable with them we may switch them to stereo, depending on what Worship leader wants to do. They are plugged into Outputs 1-6.

[BWhiteParticipant]

Sq6 is up and running. We have sound where we would like but needs alot of tweaking. I haven’t been there during service cause of work. Again have some questions.
1. I patched our Main L/R to the outputs 1 & 2 on the DX168, work fine. On layer B the first two strips are labeled Aux 1 Aux2, that if for local outputs and not the DX outputs, right?

2. If first is correct then that allow me to still use Aux 1 & 2 for local outputs for IEM’s, Right?

3. On assigning aux to Pre or Post, Go to Aux then Routing, Channel source is just where signal is being tapped from along signal chain. Assign section is if easy way to assign all channel to or from Aux? Pre-Fade section is where you assign the Aux as a Prefade or Post Fader Aux?

I have two outputs right now 1 stream and 1 FM, I believe i have them set as Post Fader.

4. Aux 13 & 14, These can’t be assigned to a layer like the other auxes can, so how do you control these? What do you assign tp these, Matrix, L/R, Group? Or is there a way you can use them as a regular aux/send?

Just to be clear have SQ6 in sound booth, DX 168 behind stage as well as an analogue snake with 12 channels coming back to booth. Right now using 4 stage monitors these being plugged in on stage floor boxes which go to the DX box. Have ran cables from board outputs 1-6 to IEMs in our rack for use in the near future (Worship Minister & I thought it would be better to get sound going and close to what we want then switch over and do some training in the mean time.) Have 1 aux for FM and another Aux for stream via Dante Avio 2 Ch doggle.

Thanks for all the great advice from before. I will be back with more questions I’m sure.

[BWhiteParticipant]

Sorry haven’t been on in a while.
After reading some of the replies, I ran 3 Cat6 Shielded cables, 1 to use 2 for future use or when needed.
Finally got our SQ6 in and been installing it this week. Still trying to figure things out. Do have sound coming from Mains via Slink to Dx169 output 1 and 2. Still just using stage monitors at this time, we did get sound finally thru these via the Slink and routing.

Going to take some time getting things figured out but we will get it.

Question: The SQ6 has 14 outputs on the back. I see that 11 & 12 where for the Main l/r, what is 134 & 14 for. I can not find Aux 13 or Aux 14 in the layer setting page. What am I missing. Would like to use these for a stream mix and FM Transmitter

[BWhiteParticipant]

Can the add on SLink card connect to a third party audio snake ike the lyxpro 4 channel audio snake. I figure it has to be A&H brand, but thought i would ask.

[BWhiteParticipant]

So we decided to go with PSM300s. We are getting 11 sets, Lead vocal/guitar (sings), bass, drums, electric guitar, acoustic guitar, keys (sings), rhythm (sings), then Vocals left, left center, right center, right (designated mic to position for ease of sound tech knowing who has which mic. Most likely running mono.

Right now we are going to pace the transmitters in the rack located in the sound booth approx 70-80′ away.

I plan on patching Main L/R(Aux 11/12) out to the DX168 Output 1 & 2 for the mains. This will open channel 11 & 12 aux for IEMs, if i’m thinking correctly?

I guess the easiest thing to do then would just patch each IEM to an aux out 1 thru 11. Plan on using the SQ4You app so each individual can setup their own mix with the help of sound tech if needed.
Or is there a better way to do this without using all the auxes. We do have a stream mix and a FM transmitter mix also. The stream is a dante AVIO 2out dongle and FM just mono.

It would be great to have the DX012 expander but that will be a future purchase.

I seen the loop out on the PSM300, and thought that all the vocals could be connected together from one mix, but then they could not adjust their in ear mix cause it coming from one source, Right?

Thank you all for your help.

[BWhiteParticipant]

Can you use the AES out to a DX012 for in-ear monitors. Patch from XLR to psm300 systems? Also is the AES stereo, mono or selectable?

[BWhiteParticipant]

Don’t have a definite on the in-ear, yet. We had priced to the board the ME system from A&H. Think Worship Minister is leaning to a hybrid mix, some wireless and some wired.

Question: Can the soft rotaries control a channel volume. EX: First layer taken up with vocals and instruments and such. Second layer would contain Pastor’s mic, another lapel mic, and computer for music. Could the soft rotaries control the volume of those channels on the second layer. Basically worship team is playing and pastor gets up to talk and needs a touch bit more volume, reach up and tweak the rotary knob and done.

[BWhiteParticipant]

The 1/4″ outputs on back would those be good to run a mix to a FM transmitter. We have some members still come that don’t do Facebook, and listen in the parking lot.

We are getting in ear monitors, hybrid of wireless and wired. Also have a stream feed that i fed off of the XR with a Dante Avio 2 out adapter, which helped tremendously with the audio of the feed.

[Author]

Posts