Forum Replies Created
-
AuthorPosts
-
2013/07/17 at 7:53 am #34473
quote:
Originally posted by Chris93Could it be related to the switch-on order? Restarting the GLD would make it be the last thing to be switched on.
Chris
It’s always the last thing to be switched on.
Anyone else with an ideas? IS there a way to send a ticket to A&H?
2012/12/11 at 6:28 am #32383Hey Berry,
I had the same problem over the weekend. What mumu said is correct… the 64 bit version of Reaper cannot connect to the ASIO driver of the Dante Soundcard. Have a look at the 5th post of the following link:
https://forum.cockos.com/showthread.php?t=68029I what I did was uninstall the 64 bit Reaper and install the 32bit version. It fixed the problem. When you go into Reaper and change the audio driver to ASIO in Audio Device tab of Preferences you should then see under that inputs and output ranges. Input range should be first: 1 Dante rx 0 and Last: 64 Dante rx 63. The Output range is the same but rx is replaced with tx. Tick the Enable inputs tab.
I found that the ilive and Dante webinar videos at the bottom of the following linked helped:
https://www.allen-heath.com/UK/Products/Pages/iLiveTrainingVideos.aspx?TOV=1&CatId=iLiveSeries&SID=36Hope that helps.
2012/12/08 at 7:45 am #32363Well, I just found out about the Reaper 64bit issue with dante. I have uninstalled it and installed the 32 bit version. Reaper now recognises the ASIO driver, Hopefully that has fixed my ASIO issues. Won’t know until I go back tomorrow morning.
2012/12/08 at 5:33 am #32362Thanks for that guys.
Now I have a few issues.
1) In the Dante Controller I am getting heaps of Events. I am getting “Timed out 3 times awaiting a reply to message ‘Versions’ from PC, giving up.” Happens every ten secs.
2) In the Dante Controller Routing view on the Dante Receivers I am getting an exclamation mark next to the Dante Card(BKLYN2-0609dc). In the transmitter section there is no exclamation mark. I assume this is linked to issue 1?
3) On the Dante Virtual Soundcard I am getting in the left bottom corner “ASIO Application: Disconnected”.
4) In Reaper I am getting an error, “There was an error while opening your hardware: Error loading ASIO driver. Would you like to view your audio device configuration?” I assume this is linked to issue 3.If anyone has had similar issues or know fixes that would be great.
2012/07/08 at 10:22 am #30965Multitouch would be great.
I’m interested in whether or not they make an app for the new Windows tablet/Windows 8.
2012/06/20 at 7:02 am #30865quote:
Originally posted by Mr BThe gain is shared,you only have one analogue pre amp. either one surface retains control of the analogue gain while the other uses the Trim control which I believe is + and – 24dB of digital gain, or, my preference is once the gains are roughly set then each surface swaps to trim mode that way no unexpected gain changes occur affecting both surfaces.
Thanks for clearing that up. Two question on the trim mode: Is it changed to trim mode for both at the master or does the slave have to change it as well? I am assuming it is done at the master. If so, does that mean there is no way that slave can accidentally change it?
I have a few other questions if you don’t mind.
I know that all mixracks provide dsp power to process up to 64 input channels no matter the number of actual physical inputs. This is fine for the iDR-16 from the iDR-64, I just go to the quick input source setup. But what about the iDR-64? If I need inputs from the iDR-16, how do I actually get those inputs if I can only have 64 inputs to the iDR-64? Or is it fine and have I misunderstood something?
Lastly, if I change a name of an input in Editor or surface for the master will this inputs name be changed for the slave? i.e I change “BkVox1” to “Suzzie” at FOH, will it also change on the media slave?
Cheers
2012/03/28 at 4:16 am #30259Excellent! Thanks.
-
AuthorPosts