Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • #103082
    Profile photo of JFugJFug
    Participant

    Agreed about the GPIO Syber, I hope they can find a way to close a GPO on a soft key. I set up a way to do it with scenes, it’s a viable option and the only issue I’ve found is if you trigger the GPO (which is actually a scene recall) a ton of times all at once it’ll freeze and sometimes straight crash the surface. But the only way you’d run into that is by forcing this issue I’d think.
    A GPO contact closure would be great.

    #103081
    Profile photo of JFugJFug
    Participant

    Thanks Dave. Sadly I’m looking for something with the feel of a monitor controller. We ended up just buying an outboard monitor controller. It’s what worked for us but the IP1,8,or 6 would have been great. I was trying to stay away from faders on the console since that’s where all our channels are and I didn’t like the idea of having the audio control room speakers volume level next to a channel or something and I didn’t have space on the board to leave a couple dead faders to space it out. I currently have the PAFL bus outputting to the out oared controller. It works just fine.

    #102616
    Profile photo of JFugJFug
    Participant

    +1, while not a NEED, it would definitely be cool! I’d also love a way to see AMM meters or something down there…

    #102615
    Profile photo of JFugJFug
    Participant

    I’ve heard rumors that being able to label actual sockets is coming, so hopefully being able to label the top row or Cardslot or DX Port would be included. It would be super cool to be able to label a DX port “Drums” or “Booth” or “wireless” or whatever would be nice. +1 from ME!!!!!!!

    #102614
    Profile photo of JFugJFug
    Participant

    +1 from me! That would be a cool feature if it’s doable!

    #102485
    Profile photo of JFugJFug
    Participant

    I would LOVE to be able to see the current scene. We have scenes based on each song that’s done at our church as well as scenes for the sermon and welcome and ending, so its nice to know what one you’re on and it would be cool to see current/next or something!
    Thanks AH!

    #102484
    Profile photo of JFugJFug
    Participant

    I agree. More groups would be nice or just the ability to actually see all the channels at once (like the MX32 monitor app). The 4 groups is nice, but it would be really cool to have more control at once!

    #102483
    Profile photo of JFugJFug
    Participant

    You aren’t missing anything. IT’s weird. The faders snap immediately but the fades should be actually happening. Sadly the faders just don’t show it.

    #101395
    Profile photo of JFugJFug
    Participant

    +1 as well. That and some other direct out or pick point options!

    #100596
    Profile photo of JFugJFug
    Participant

    Hey Nikola!

    Thanks for getting back to me.

    I figured the headphone knob was analogue but it’s always worth asking. Now I know.

    I’ve used the IEM PAFL fader before but prefer something away from all my other faders for monitor control. It’s just safer. I’ll keep the PAFL back into a matrix idea though. I’ve played with it a bit and it could be VERY useful.

    Thank you SO MUCH for adding port names in the new firmware. That’s HUGE! Thanks for always listening snd making your products better and better!

    I’ll look into your scene idea. I’m currently using embedded recall and have one scene turn a fader on and another turn it back off after .2 seconds. Works well enough but can crash or freeze the surface if done too many times in rapid succession. All in all, it’s not a huge deal. I’ll keep the scope for just GPIOs in mind though. That’s really sharp.

    The one reason I don’t like using tielines for certain things is sometimes patching changes on the fly and direct outs hold the patching where as with a tie-line, I now have to go and re patch. This was less for broadcast and more for FOH/Mons/Streaming setups I do for churches. It’s a lot easier if only FOH has to keep track of patching.

    As always, thanks for your expertise and time and the fact that AH is always making things better!

    #79476
    Profile photo of JFugJFug
    Participant

    Actually. I could see where this would be super helpful in festival situations. DigiCo already does it. You can go to the input patch screen and it shows all available inputs with any active inputs with meters so you can see what inputs have channels.
    If A&H could do something similar somehow. That could actually be really cool.

    #79282
    Profile photo of JFugJFug
    Participant

    I’d also like to +1 this. It would be extremely helpful for all kinds of uses to have the pick/tap points of Direct Outs be channel specific.
    Thanks!

Viewing 12 posts - 1 through 12 (of 12 total)