– PAD in QU Mixers

Forums Forums Qu Forums Qu general discussions – PAD in QU Mixers

This topic contains 9 replies, has 8 voices, and was last updated by Profile photo of Mike C Mike C 1 year, 6 months ago.

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • #71290
    Profile photo of Vijkan
    Vijkan
    Participant

    The Analog A&H Mixers had an PAD Option for signals that were too strong coming into the Mixer. I recently connected output of an Guitar Amp to the input of my QU-24 and felt that the Input Signal was too strong. The only option i had was to turn the Gain to -Negative. Is there a better solution.

    #71292
    Profile photo of Giga
    Giga
    Participant

    You could use an inline pad….

    I have splitters in my rack which also have pads.

    Giga

    #71313
    Profile photo of Vijkan
    Vijkan
    Participant

    So there is no in-built option?.

    #71314
    Profile photo of Mfk0815
    Mfk0815
    Participant

    I personally prefer digital mixers without a dedicated PAD-switch. It should be easily to design a gain range which makes an extra PAD obsolete. The advantage of this extended gain range is that you can simply lower the gain if the signal becomes hotter during the performance because of the extra adrenaline of the musicians. If the gain is on the lower end of its range and you have to press the PAD you will lower the gain by a fixed value (e.g 20 dB) instead of just some dB.
    Just my 2cents

    #71317
    Profile photo of garyh
    garyh
    Participant

    If you use a dSnake stage box, the input screen on the board includes a pad switch.

    #71335
    Profile photo of airickess
    airickess
    Participant

    Was this output on the guitar amp the XLR output? Those are typically mic level, but if it is not, then you can use an XLR to 1/4-inch adapter and go into the Line input of the channel rather than the Mic level input.
    You can also look on the guitar amp and see if there is a switch on the output that switches the signal between Mic and Line.
    If you used another output of the guitar amp, chances are that you might have used an amplified signal meant to drive a speaker cabinet and that certainly would have put out a very hot signal.

    #71338
    Profile photo of Vijkan
    Vijkan
    Participant

    Thanks to all for your valuable responses.

    @garyh – dSnake presently is the next to get dream due to the $$$. But thanks, it helps to know that.

    @airickess – I will certainly check next time. On this occasion the entire setup was delayed so we had to rush everything. But i feel the MIC Switch makes sense. I initially used 1/4 on Amp to XLR on QU-24, this was too hot, i then changed it to 1/4 to 1/4 and it was better. But your input gives me something to look for in the next gigs.

    Thanks.

    #71344
    Profile photo of MarkPAman
    MarkPAman
    Participant

    Very unusual to find an output from a guitar amp, that sounds better, or as good, as putting a mic on the cab.

    #71347
    Profile photo of Dick Rees
    Dick Rees
    Participant

    Very unusual to find an output from a guitar amp, that sounds better, or as good, as putting a mic on the cab.

    Yup. And NOT unusual for instrument amp line outs to be noisy. My preferred method is a dry direct via DI before anything else and then a mic on the cab to get the FX/processed sound. A lot of patches have no “center” to the sound and turning up the solo just doesn’t work without a bit of clean signal mixed in for support. The intended sound is still there and predominant, but now there’s something more to let it come out in the mix as it should. Fuzz tones and distortion are the worst offenders.

    #71350
    Profile photo of Mike C
    Mike C
    Participant

    I can’t remember the amp model but I had a guitar play who’s amp
    had a direct XLR out from an internal cabinet emulator DI that actually
    sounded good.

    In the right hands the amp modelers and processors sound very good.

Viewing 10 posts - 1 through 10 (of 10 total)

You must be logged in to reply to this topic.