Topic: suggestion for the next update | Allen & Heath Digital Community

suggestion for the next update

This topic has 82 replies, 41 voices, and was last updated 13 years, 9 months ago by Anonymous.

Viewing 15 posts - 1 through 15 (of 83 total)

1 2 3 4 5 6 →

Author

Posts
2010/07/27 at 5:10 pm #22394

selfmade
Participant

first of all, thanx for your wunderful support!
i´m very excited for the next update, and have some urgent wishes.

– an phase switch on the mix out´s
– an hi-/low-cut on the mix out´s
– maybe an phase option from 0 to 180 degree´s on the mix out´s

please help my work with that update´s!

greetings from hamburg

2010/07/28 at 2:19 pm #25965

ddff_lv
Participant

I agree on HPF & LPF for certain mix outputs. Phase switch – would it be polarity? Phase is time and delay is already there. Polarity would be good, yes. Phase from 0 … 180 deg – was it intended as all-pass filter?

ddff

2010/07/28 at 2:49 pm #25966

martijn
Participant

Phase switch is there! (direct input menu)
HI/LO cut is there!! (set your filters to do 20Hz-20KHz and you can sweep them all over the place!)

2010/07/29 at 4:57 am #25970

josiaspicone
Participant

A LPF (crossover filter) could be usefull for sub aplications… and phase on mixes would be great too.

Cheers

Solo se que no se nada

2010/07/29 at 7:57 am #25971

Biggsounds
Participant

I think this has been mentioned previously, but separating the MUTE & PAFL buttons in Editor would be VERY appreciated – they’re too close for comfort in the heat of battle! Also, would it be viable to enable all the softkey functions in editor (ie allow the Mix & Sel functions to operate correctly in the softkey simulation the way all the other functions already do)?

iDR32 mixrack
Asus N61 Laptop (x2 wireless)
Sennheiser IEM (for PFL)
Dante card (soon!)

2010/07/29 at 8:17 am #25972

Anonymous
Inactive

Softkey ‘banks’ would be great too. They’re already capable of so much that eight doesn’t seem to be enough sometimes. And timed fader position changes between scenes would be lovely.

T112, R72
iDR32, iDR48
iStuff

2010/07/30 at 6:25 pm #25974

jheimberg
Participant

Id like to just echo an earlier thought from the other thread: It would be great to be able to link 2 of the three banks (t112).

Also – it may be a stretch, but independent (even basic) channel EQ’s for aux sends… so we can have a true virtual monitor board with the wifi tablet.

AND: It would be nice to be able to enlarge/customize the sliders in the editor software – it would make it easier to do MON from on stage with the tablet.

Thanks!

http://www.soundadvicetraining.com

2010/08/02 at 2:15 am #25979

dnxmirrorsounds
Participant

Can I revisit having a width control on stereo channels please?

Duncan Whitcombe
Mirror Sounds & metrochurch
Perth, Australia
T112, iDR48x2, Dante soon
http://www.mirrorsounds.com.au
http://www.metrochurch.org.au

2010/08/02 at 2:20 am #25980

dnxmirrorsounds
Participant

Oh yes,

and the ability to set the direct out feed source per channel rather than global.

Duncan Whitcombe
Mirror Sounds & metrochurch
Perth, Australia
T112, iDR48x2, Dante soon
http://www.mirrorsounds.com.au
http://www.metrochurch.org.au

2010/08/02 at 5:08 am #25984

dnxmirrorsounds
Participant

Oh, another thing, can DCA PAFL be post-fade for the channels that are controlled by the DCA so that we can get an idea of the DCA mix? If Possible

Duncan Whitcombe
Mirror Sounds & metrochurch
Perth, Australia
T112, iDR48x2, Dante soon
http://www.mirrorsounds.com.au
http://www.metrochurch.org.au

2010/08/02 at 7:58 am #25986

selfmade
Participant

hey duncan,
it´s already, if you activate the “input afl” mode on the surface.

greetings from hamburg

2010/08/02 at 8:18 am #25987

dnxmirrorsounds
Participant

cool, I’ll look for it. thanks,

Duncan Whitcombe
Mirror Sounds & metrochurch
Perth, Australia
T112, iDR48x2, Dante soon
http://www.mirrorsounds.com.au
http://www.metrochurch.org.au

2010/08/02 at 1:36 pm #25989

kentlowt
Participant

Resizable channel strips in the edit so you don’t have to use your glasses everytime you want to click on the mix,select PAFL etc. Or maybe easier <alt> z for zoom in and magnifies to a preset value the strip your working on.

112T/IDR48/IDR16

2010/08/02 at 6:01 pm #25991

Biggsounds
Participant

BIG + for the resize feature in editor (particularly for the touchscreen usability)!!!

iDR32 mixrack
Asus N61 Laptop (x2 wireless)
Sennheiser IEM (for PFL)
Dante card (soon!)

2010/08/02 at 6:20 pm #25992

Stix
Participant

quote:

Originally posted by whitcodj

Can I revisit having a width control on stereo channels please?

+ 1 I aggree on that – at the moment if you lose one channel of a stereo source the only way to make the remaining channel mono (ie to feed both L & R outputs) is to assign through a group. If you don’t have a group set up then this can take valuable time. Also sometimes stereo sources need to be mono’d up a bit live so the audience can hear both parts if they near to only one PA stack.

Cheers

Richard Howey
Audio Dynamite Ltd
IDR48/IDR16/T112/R72
Author

Posts